|
|
Post by dubehigh on Feb 17, 2010 15:23:12 GMT -6
hey sol or doozer, take a look at this, the red is - and the black is+ how do i check this so its right,  |
|
Raygun
Moderator 
FIRST 30 MEMBER
The needs of the many out weigh the needs of the few
Posts: 1,567
|
Post by Raygun on Feb 17, 2010 15:39:14 GMT -6
That does not seem right put a dc voltmeter on it and see if it gives you a positive or negitive reading on the motor outputs.. Ray
|
|
|
|
Post by dubehigh on Feb 17, 2010 19:45:43 GMT -6
hey ray, yea i did that and the decal is wrong. so nw i have a nother problem, i got he neon to bind to the tx, but its full throttle. all the servos work the right way, but now i have to figure out the brushed speed controler.  |
|
|
|
Post by Solitaire on Feb 17, 2010 21:19:01 GMT -6
You sure you don't wanna go brushless now? ;D
I've never had a heli with a separate brushed ESC, so I can't say if the throttle range needs to be setup on those or not. Were there any directions with the ESC?
Does it throttle down as you raise the stick? Maybe throttle reversing might work. Just guessin' here, bud.
|
|
|
|
Post by dubehigh on Feb 17, 2010 21:32:45 GMT -6
sol, i tried the stick all the way up and same thing, i am not sure on how to set the dx6i for this also. worse case if i cant figrue it out i will go to brush less, but i would like to try this first.  |
|
|
|
Post by Solitaire on Feb 17, 2010 22:24:56 GMT -6
Well, I just checked a Castle Creations and an Electrify brushed ESC online and both have to be setup for throttle range, so I'm guessing yours does as well.
BTW, looking at your pic above, are the Rx connections the right orientation? I'm sure you have it right, but it's hard to tell from the pic.
|
|
|
|
Post by Solitaire on Feb 17, 2010 22:27:46 GMT -6
Hey, I need that super long anti-rotation bracket you have in the package there. ;D
|
|
|
|
Post by dubehigh on Feb 17, 2010 22:39:23 GMT -6
as far as i no there all right, all the servo work right, speed controler goes to the thro right?
the anti you looking at is for the gaui, but i dont need it.
|
|
BTCat
First 30 Member 
FIRST 30 MEMBER
BT Cowboys Cruiser
Posts: 2,213
|
Post by BTCat on Feb 18, 2010 6:05:23 GMT -6
as far as i no there all right, all the servo work right, speed controler goes to the thro right? the anti you looking at is for the gaui, but i dont need it. It's right. But at first, second and third look, it looked like the ESC was hooked to the BATT connector on the RX. Just the angle of the picture. BTW, no answer on the throttle. But I have read of others having issues setting their full throttle with the brushed ESC. Apparently it is a common problem. I'll go back and see if I find how they fixed it. |
|
BTCat
First 30 Member
FIRST 30 MEMBER
BT Cowboys Cruiser
Posts: 2,213
|
Post by BTCat on Feb 18, 2010 6:13:26 GMT -6
|
|
Raygun
Moderator
FIRST 30 MEMBER
The needs of the many out weigh the needs of the few
Posts: 1,567
|
Post by Raygun on Feb 18, 2010 8:09:14 GMT -6
I have a couple of e-sky 20 amp esc's for brushed motors your welcome to try one if you like. I have lightened them up and they work perfect. As far as throttle reversal the DX6I is real easy to reverse the throttle or any channel. Ray
|
|
|
|
Post by dubehigh on Feb 18, 2010 10:10:37 GMT -6
THANKS GUYS, well i just orderd a brushless system for it. i should have done that in the first place, so i orderd a 3100kv motor. and a 25amp esc. should be here next week
bt i looked at that thread, and it came to no conclusion that i could find for what is going on with it, i do have one more thing i am going to try why i wait on the new parts
|
|
|
|
Post by Solitaire on Feb 18, 2010 22:24:53 GMT -6
Well, you could trade Ray an Esky charger for one of his brushed ESC's while you wait, too.  |
|
